Esu 54688 2 Piece Locomotive Driver Micro V4.0, MM / DCC/SX New Boxed

If you buy after clicking affiliate links on this site we might receive a commission from companies such as eBay, Amazon etc This does not affect the price you pay.

If you buy after clicking affiliate links on this site we might receive a commission from companies such as eBay, Amazon etc This does not affect the price you pay.
Click here to see similar items on eBay, and to buy.

Esu 54688 2 Piece Locomotive Driver Micro V4.0, MM / DCC/SX New Boxed

The description of this item has been automatically translated. If you have any questions, please feel free to contact us.

2 piecesLokPilot micro V4.0, MM / DCC / SX, 6-pin. NEM 651 direct

The LokPilot V4.0 is only 10.5 mm x 8.1mm x 2.8mm small and should therefore also find its place in the smallest locomotives of the nominal sizes N or TT.

Operating modes
The LokPilot micro V4.0 recognizes the DCC, Selectrix and Motorola protocol. In DCC mode, it can be operated with 14, 28 or 128 speed steps or used on analog DC systems. You can either use two-digit or Use three-digit (1-127) or four-digit (1-9999) addresses or assign a traction address (consist address).
The Motorola protocol enables the decoder to be operated with Mrklin central units 6020, 6021, delta, mobile station and central station. He masters the addresses 01 – 255. A second address enables switching from F5 to F8 if required.
The Selectrix protocol enables the LokPilot V4.0 decoder to be used with these proven systems.
All common DCC brake systems such as the well-known Lenz LG100, but also the new Lenz ABC brake modules with asymmetrical DCC signal are taken to heart, as is braking in the DC section with reverse polarity (Brake on DC) or the Selectrix diode braking system. The Mrklin braking system can also be used – even in DCC operation. Of course, the decoder can also calculate a constant braking distance, so that your locomotives always stop correctly in front of the red signal regardless of the speed. Of course, LokPilot micro V4.0 decoders can also be used on analog DC systems.
The decoder can switch between Allen operating modes (Motorola, DC, DCC, Selectrix) fully automatically during operation.
Engine control
The LokPilot micro V4.0 with load control is the improved 5. Generation.
The control frequency can be adapted adaptively to the speed at a base frequency of 40 kHz and ensures an even better, silky smooth, absolutely quiet engine running for many engines. The 10 bit A / D converter lets your locomotives crawl super slowly on the layout. With Dynamic Drive Control (DDC) you limit the influence of the load control and can regulate sensitively in the station and switch area, while on the (fast) route the locomotive slows down prototypically when driving uphill.
The load control copes perfectly with Allen common motors, whether from ROCO, fleischmann , Brawa, Bemo, Faulhaber or Maxon. 0.75A continuous current are for the above
mentioned engines more than sufficient and offer enough power reserves even for long block trains.
Analog operation
The LokPilot micro 4.0 decoder can also be used on analog DC trains.
Functions
The LokPilot micro V4.0 decoder has two function outputs, each with 150mA continuous current, which can be individually assigned a function. Two additional unamplified outputs can also be used to control special functions using an external transistor. There are all important lighting functions such as flashing lights, strobes, alternating flashers, firebox simulation, etc. to disposal. The brightness of each output can be set separately. The decoder masters the automatic connection and disconnection when uncoupling for couplings and now also offers a high beam function. The “LED mode” ensures correct lighting effects when using LEDs.
Operational safety
If required, you can connect a Powerpack to the LokPilot micro V4.0 (ESU 54670, see page 62). This energy store supplies the decoder with energy when the power consumption is not optimal due to dirty rails.
RailComPlus
With RailComPlus, the decoder now automatically registers with suitable control centers and receives a new address if required.
Future built in
LokPilot decoders are firmware update capable.If you need more, please email us see photo Postage is paid by the buyerHappy biddingfurther information and general terms and conditions under “me side”Toys and trains at Eisenbahneck GmbH Fr.-L.-Jahnstr. 8 31582 Nienburg
All of our items are not suitable for children and adolescents under the age of 15. Before buying, we ask you to send us an email that you have read the age limit and warnings.
All items areSmall scale model true to scale and original for adult collectors.
The stated prices are only valid on Ebay and not in our shop. Collection is not possible at the eBay price.
Toys and trains at Eisenbahneck GmbH Fr.-L.-Jahnstr. 8 31582 Nienburg 2 pieces LokPilot micro V4.0, MM / DCC / SX, 6-pin. NEM 651 direct Operating modes The Selectrix protocol enables the LokPilot V4.0 decoder to be used with these proven systems. Engine control The LokPilot micro V4.0 with load control is the improved 5. Generation. Analog operation The LokPilot micro 4.0 decoder can also be used on analog DC trains. Functions Operational safety RailComPlus Future built in LokPilot decoders are firmware update capable. If you need more, please email us see photo Postage is paid by the buyer Happy bidding further information and general terms and conditions under “me side” Toys and trains at Eisenbahneck GmbH Fr.-L.-Jahnstr. 8 31582 Nienburg All items areSmall scale model true to scale and original Marke Esu Baugre (Spurweite) Spur H0 (16,5 mm) ISBN Nicht zutreffend EAN Nicht zutreffend MPN 54688 Produktart 2 Elektrik & Elektronik Stromversorgung Wechselstrom Herstellernummer 54688 Przise Produktart Elektrik & Elektronik Produktart Zubehr

Category: Collectables:Model Railways and Trains:Power and Control:Digital control devices
Location: Nienburg